Skip to content
Cart
Checking your vehicle…

Rival Performance brake packages contain top-tier aftermarket brake discs without the premium price tag, and are paired with either EBC or PBS brake pads that have been widely performance tested. 

We have taken all the hard work out for you, if you need replacement or upgraded brake discs, brake pads and braided brake lines then this is the listing you need!

Super user friendly, easy to use with tried and tested performance products that we have personally used on the road, and race circuit.

A truly tried & tested brake package!

Rival Performance Brake Package Contains:

  • 1x Set of Rival Performance Brake Discs (253x10mm)
  • 1x Set of Performance Brake Pads

BRAKE FLUID NOTICE:
Brake fluid is overlooked when it comes to braking performance, because it is invisible. It works during normal road use driving, but fails when pushing the car. Regardless of how low the mileage is, brake fluid is hygroscopic, meaning it absorbs moisture directly through the rubber brake hoses and reservoir seals over time. Moisture is even absorbed from the air when the car sits parked. Most car manufacturers specify a full system brake fluid flush every 24 months (it is in the service schedules, but tends to be overlooked). Even a 2-3% water content can drop a brake fluid's boiling point by over 60°C!

When on a spirited drive or on a track day, especially when running brake pads that deal with heat which transfers onto the brake caliper pistons. The already absorbed water then turns to steam, creating compressible gas pockets and causing the brake pedal to drop straight to the floor. Most upgrade their brake pads first because they want better stopping power. However, the better/higher-friction brake pads generate far more heat to allow you to brake later, pushing the brake caliper temperatures well past what the standard brake fluid can survive.

For everyday normal use with spirited driving, brake fluid should be replenished every 6-18 months (depending on conditions and actual use). For track/race days, you should bleed a small amount of brake fluid from each brake caliper after taking part, but if the brake pedal is softer than normal or wanting optimal braking performance, perform a full brake fluid flush before the next outing.

To add brake fluid to your order, CLICK HERE.

Fast Road, Track Day & Race Brake Pad Recommendations:
When it comes to braking in FWD cars, the majority of the braking performance comes from the front so that is the area to be focusing on for massive brake gains, however the rear brakes do play a small part and benefit when upgraded.

FAST ROAD USE:
For the general fast road user, EBC Ultimax2 is a solid starting point over stock. If wanting better, then EBC Yellowstuff is the brake pad compound to go for. Both compounds work from cold and are R90 approved to be driven on public roads

EBC Ultimax2 brake pads produce low-to-moderate brake dust similar to the original equipment and are considered gentle on the brake discs. EBC Yellowstuff brake pads let off moderate to high brake dust, and are also considered gentle on the brake discs.

The EBC Ultimax2 bedding-in procedure can self-seat gradually during everyday commuting, where as EBC  Yellowstuff brake pads can require a longer bedding-in time (bedding in procedure requires multiple heat cycles for heavy use).

TRACK DAY USE:
Because the majority of braking comes from the front (70% front/30% rear), it's not uncommon to see either

EBC Ultimax2, Yellowstuff, Bluestuff or PBS ProTrack. EBC Ultimax2 is a road pad, Yellowstuff is a fast-road performance pad, whereas EBC Bluestuff is a higher-friction, track-capable hybrid brake pad built to handle repeated heavy braking. While all compounds work from cold and can be driven on public roads, EBC Bluestuff can be used on the race circuit where as EBC Ultimax2 and Yellowstuff is not recommended due to heat.

If driving to the race circuit, then EBC Ultimax2, Yellowstuff or Bluestuff are the better choices due to being R90 approved for UK road use.

EBC Bluestuff brake pads let off moderate to high brake dust, and are aggressive on the brake discs. PBS ProTrack brake pads also let off moderate to high brake dust, and are aggressive on the brake discs. EBC Bluestuff bedding-in procedure is a fast bedding-in process. PBS ProTrack brake pads bedding-in procedure is also a fast bedding-in process.

RACE USE:
For those who are using the car for extreme circuit use, it tends to be a bit of a mix of which brake pads to use due to driving styles etc. Similar to track day use recommendations, it is not uncommon to see EBC Yellowstuff, Bluestuff, PBS ProTrack or PBS ProRace.

It certainly depends on what you has been used and the driving style, again when it comes to superior performance braking, brake pad dust is inevitable. All these types of brake pad compounds will produce brake dust.

How to Bed-in:

The best way to bed in new brake discs is to use them gently over the first few hundred miles, not getting them too hot and letting them cool gently. Try to avoid hard braking during this time (safety considered).

Because new brake pads will be paired with the new brake discs, follow the bed-in procedure for the brake pads being installed.

EBC Ultimax2/Yellowstuff™ Brake Pads Bedding-in Procedure:

EBC brake pads are now mostly self bedding, but for extreme street use please read below.

The Ultimax2, Greenstuff, Redstuff, and Yellowstuff compound grades come with a brake-in coating that scrubs the rotor surface, accelerates pad seating times, and provides a strong brake effect for the first 100 miles of use as the brake pads seat themselves. After the first 100 miles or so, unless you are going to drive aggressively, there is nothing more to do meaning – most drivers happily use and enjoy their brake’s excellent performance for tens of thousands of miles after this point. If that’s your way of driving, nothing more needs to be explained. Just enjoy your brakes.

Fast Street Driving:

If you drive aggressively or in a “Spirited” fashion on roads where it is safe to do so, after seating the pads to your rotors and certainly not before 300 miles of use , you should be prepared for the brake pad to emit an odour or even exhibit some smoke as the pads burn off what EBC call “surface volatiles”.

Many faster drivers experience this in harder braking and criticize the brake pad whereas in fact, this is only part of the final high-end bedding-in process as the pads see rotors temps of 400-500C for the first time (not normal in everyday driving).

Once seated, any organic brake pad made by EBC performs better once the pad goes through heat curing or what EBC call “Green Fade” which happens during its first severe use. The green fade point is 400C/650F. There are two ways to know if you have passed the green fade point – one is via the use of heat paints, the second way is to guess. So heat paints are the better option.

You should drive with caution until bedded flat and you have passed this green fade point at least twice and then allowed the brake pads to cool so the disc is below 100C.

Fast Street use Pre-bed:

FADE 1 – drive 50 to 100 miles on Public road/highway normal driving to allow the pads to mate up to the disc and establish full contact followed by 8 stops from 80 mph to 30 mph at 300-yard intervals and then coasting allowing the brakes to cool.

Wanting to use Yellowstuff on the track?

EBC Yellowstuff are no longer optimum for track use. Bed in times are simply too long to be acceptable. Having said that if you LIKE Yellowstuff and want to use them at the track be prepared for the longer bed-in times detailed below.

Yellowstuff, although track-capable, is no longer recommended for track use on most cars due to its long bed-in the process. Bluestuff is now EBC's recommended entry-level race pad for all vehicles, which as a track hybrid is still great on the street and even better on track. But if you are to use Yellowstuff on the track, follow the below Fade procedures;

FADE 2 – After the basic street pre-bed above is performed on the road or at the track if installed there, perform 10 medium pressure snubs at the track from 80-20mph leaving 300 meters between each snub (approx 0.4g decel). Allow pads to cool for 15 minutes minimum after coasting to the pits allowing brakes to cool a little.

FADE 3 – Perform 6 high-pressure snubs from 90-20mph with a maximum acceleration between consecutive snubs. (approx 0.8g decel, or 80% of an emergency stop). Allow the brakes to fully cool for a minimum of 1 hour before the race session. EBC advise using disc heat paint to ensure green fade is avoided.

EBC Bluestuff™ Brake Pads Bedding-in Procedure:

Perform the street pre-bed Fade 1 routine as below (either on the road or at the track if installed there ) followed by Fade 2 at the race track. The latest Bluestuff DM3362 and Low Mu versions should only take Fade 2 and a 15 minute cooling time to be ready to race.

Fade 3 should not be necessary unless poor disc condition has prevented proper seating, but if you have time DO perform Fade 3.

Fast Street use Pre-bed:

FADE 1 – drive 50 to 100 miles on Public road/highway normal driving to allow the pads to mate up to the disc and establish full contact followed by 8 stops from 80 mph to 30 mph at 300-yard intervals and then coasting allowing the brakes to cool.

Track/Race Pre-bed:

FADE 2 – After the basic street pre-bed above is performed on the road or at the track if installed there…..Perform 10 medium pressure snubs at the track from 80-20mph leaving 300 meters between each snub (approx 0.4g decel). Allow pads to cool for 15 minutes minimum after coasting to the pits allowing brakes to cool a little.

FADE 3 – Perform 6 high-pressure snubs from 90-20mph with a maximum acceleration between consecutive snubs. (approx 0.8g decel, or 80% of an emergency stop). Allow the brakes to fully cool for a minimum of 1 hour before the race session. EBC advise using disc heat paint to ensure green fade is avoided.

PBS ProTrack/ProRace Brake Pad Bedding-in Procedure:

PBS brake pads are put through a heat curing treatment during the manufacturing process and 'burns out' unwanted materials in advance, reducing the gases that can cause brake fade. Because of this treatment, PBS brake pads only require light 'bedding in'.

It is recommend to perform 10 stops at low pressure and low temperature from 90MPH to approximately 50MPH, and the distance between each brake stop is to be approximately 600 to 800 meters.

PBS brake pads should be bedded in until they are up to mid range working temperature and then allowed to cool properly. Doing this process will help to remove any gases that were in the brake pad compound and will create a perfect contact pattern between the brake disc and the brake pads.

BRAKING NOTICE:
Never hold the brake pedal down when hot. Coming to a dead stop and holding the footbrake while brake discs are glowing hot will imprint uneven pad deposits onto the brake disc rotor and cause vibration. This is a big NO NO. Always perform a brake cool down drive or perform cool down laps if on a race track to prevent this! 

note: image is for illustration purposes and may differ on delivery.