Rival Performance Front Brake Package (FRONT) - Ford Fiesta ST180/ST200 MK7
Order within for dispatch today
Find parts for your car
Choose an exact version
Choose a version from this store's reviewed vehicle collections.
No saved vehicles yet.
Rival Performance brake packages contain top-tier aftermarket brake discs without the premium price tag, and are paired with either EBC or PBS brake pads that have been widely performance tested.
We have taken all the hard work out for you, if you need replacement or upgraded brake discs, brake pads and braided brake lines then this is the listing you need!
Super user friendly, easy to use with tried and tested performance products that we have personally used on the road, and race circuit.
A truly tried & tested brake package!
Rival Performance Brake Package Contains:
- 1x Set of Rival Performance Brake Discs (278x23mm)
- 1x Set of Performance Brake Pads
- 1x HEL Performance Braided Brake Line Kit (optional)
BRAKE FLUID NOTICE:
Brake fluid is overlooked when it comes to braking performance, because it is invisible. It works during normal road use driving, but fails when pushing the car. Regardless of how low the mileage is, brake fluid is hygroscopic, meaning it absorbs moisture directly through the rubber brake hoses and reservoir seals over time. Moisture is even absorbed from the air when the car sits parked. Most car manufacturers specify a full system brake fluid flush every 24 months (it is in the service schedules, but tends to be overlooked). Even a 2-3% water content can drop a brake fluid's boiling point by over 60°C!
When on a spirited drive or on a track day, especially when running brake pads that deal with heat which transfers onto the brake caliper pistons. The already absorbed water then turns to steam, creating compressible gas pockets and causing the brake pedal to drop straight to the floor. Most upgrade their brake pads first because they want better stopping power. However, the better/higher-friction brake pads generate far more heat to allow you to brake later, pushing the brake caliper temperatures well past what the standard brake fluid can survive.
For everyday normal use with spirited driving, brake fluid should be replenished every 6-18 months (depending on conditions and actual use). For track/race days, you should bleed a small amount of brake fluid from each brake caliper after taking part, but if the brake pedal is softer than normal or wanting optimal braking performance, perform a full brake fluid flush before the next outing.
To add brake fluid to your order, CLICK HERE.
Fast Road, Track Day & Race Brake Pad Recommendations:
FAST ROAD USE:
For the general fast road user, EBC Yellowstuff is a solid starting point over stock. If wanting better, then EBC Bluestuff is the brake pad compound to go for. EBC Yellowstuff is a fast-road performance pad, whereas EBC Bluestuff is a higher-friction, track-capable hybrid brake pad built to handle repeated heavy braking. While both compounds work from cold and can be driven on public roads, EBC Bluestuff can be used on the race circuit where as EBC Yellowstuff is not recommended.
EBC Yellowstuff brake pads let off moderate to high brake dust, and are considered gentle on the brake discs. EBC Bluestuff brake pads also let off moderate to high brake dust, but are more aggressive on the brake discs. EBC Yellowstuff brake pads can require a longer bedding-in time (bedding in procedure requires multiple heat cycles for heavy use) whereas EBC Bluestuff bedding-in procedure is much faster.
TRACK DAY USE:
If driving to the race circuit, then EBC Bluestuff the solid choice due to being R90 approved for UK road use as well as being a track-capable hybrid brake pad, built to handle repeated heavy braking. EBC Bluestuff is practical for driving to the circuit, competing, and then driving home without swapping the brake pads. If wanting better, then PBS ProRace is the next step to take as they are rated for higher working temperatures of up to 800 degree Celsius, with a 0.36-0.58µ friction range and a ceramic-graphite compound that is focused on pedal modulation with fade resistance under heavy heat, compared to EBC Bluestuff's 550 degree Celsius, with friction typically around 0.42–0.52µ.
EBC Bluestuff brake pads let off moderate to high brake dust, and are aggressive on the brake discs. PBS ProRace brake pads also let off moderate to high brake dust, and are aggressive on the brake discs. EBC Bluestuff bedding-in procedure is a fast bedding-in process. PBS ProRace brake pads bedding-in procedure is also a fast bedding-in process.
RACE USE:
For those who are using the car for extreme circuit use, we advise either PBS ProComp or EBC RPX/RP1 as they are a much more aggressive brake pad. When it comes to superior performance braking, brake pad dust is inevitable. With these types of brake pad compounds you will experience brake dust, along with more apparent brake noise. But these brake pads will give you mass amounts of confidence and perform better once heat is involved.
PBS ProComp need bedding-in and are built for extreme heat along with endurance/sprint racing. Whereas EBC RPX/RP1 prioritizes instant cold bite and fast track bedding for sprints, hill climbs, and aggressive circuit use.
How to Bed-in:
The best way to bed in new brake discs is to use them gently over the first few hundred miles, not getting them too hot and letting them cool gently. Try to avoid hard braking during this time (safety considered).
Because new brake pads will be paired with the new brake discs, follow the bed-in procedure for the brake pads being installed.
EBC Yellowstuff™ Brake Pads Bedding-in Procedure:
EBC brake pads are now mostly self bedding, but for extreme street use please read below.
The Ultimax2, Greenstuff, Redstuff, and Yellowstuff compound grades come with a brake-in coating that scrubs the rotor surface, accelerates pad seating times, and provides a strong brake effect for the first 100 miles of use as the brake pads seat themselves. After the first 100 miles or so, unless you are going to drive aggressively, there is nothing more to do meaning – most drivers happily use and enjoy their brake’s excellent performance for tens of thousands of miles after this point. If that’s your way of driving, nothing more needs to be explained. Just enjoy your brakes.
Fast Street Driving:
If you drive aggressively or in a “Spirited” fashion on roads where it is safe to do so, after seating the pads to your rotors and certainly not before 300 miles of use , you should be prepared for the brake pad to emit an odour or even exhibit some smoke as the pads burn off what EBC call “surface volatiles”.
Many faster drivers experience this in harder braking and criticize the brake pad whereas in fact, this is only part of the final high-end bedding-in process as the pads see rotors temps of 400-500C for the first time (not normal in everyday driving).
Once seated, any organic brake pad made by EBC performs better once the pad goes through heat curing or what EBC call “Green Fade” which happens during its first severe use. The green fade point is 400C/650F. There are two ways to know if you have passed the green fade point – one is via the use of heat paints, the second way is to guess. So heat paints are the better option.
You should drive with caution until bedded flat and you have passed this green fade point at least twice and then allowed the brake pads to cool so the disc is below 100C.
Fast Street use Pre-bed:
FADE 1 – drive 50 to 100 miles on Public road/highway normal driving to allow the pads to mate up to the disc and establish full contact followed by 8 stops from 80 mph to 30 mph at 300-yard intervals and then coasting allowing the brakes to cool.
Wanting to use Yellowstuff on the track?
EBC Yellowstuff are no longer optimum for track use. Bed in times are simply too long to be acceptable. Having said that if you LIKE Yellowstuff and want to use them at the track be prepared for the longer bed-in times detailed below.
Yellowstuff, although track-capable, is no longer recommended for track use on most cars due to its long bed-in the process. Bluestuff is now EBC's recommended entry-level race pad for all vehicles, which as a track hybrid is still great on the street and even better on track. But if you are to use Yellowstuff on the track, follow the below Fade procedures;
FADE 2 – After the basic street pre-bed above is performed on the road or at the track if installed there, perform 10 medium pressure snubs at the track from 80-20mph leaving 300 meters between each snub (approx 0.4g decel). Allow pads to cool for 15 minutes minimum after coasting to the pits allowing brakes to cool a little.
FADE 3 – Perform 6 high-pressure snubs from 90-20mph with a maximum acceleration between consecutive snubs. (approx 0.8g decel, or 80% of an emergency stop). Allow the brakes to fully cool for a minimum of 1 hour before the race session. EBC advise using disc heat paint to ensure green fade is avoided.
EBC Bluestuff™ Brake Pads Bedding-in Procedure:
Perform the street pre-bed Fade 1 routine as below (either on the road or at the track if installed there ) followed by Fade 2 at the race track. The latest Bluestuff DM3362 and Low Mu versions should only take Fade 2 and a 15 minute cooling time to be ready to race.
Fade 3 should not be necessary unless poor disc condition has prevented proper seating, but if you have time DO perform Fade 3.
Fast Street use Pre-bed:
FADE 1 – drive 50 to 100 miles on Public road/highway normal driving to allow the pads to mate up to the disc and establish full contact followed by 8 stops from 80 mph to 30 mph at 300-yard intervals and then coasting allowing the brakes to cool.
Track/Race Pre-bed:
FADE 2 – After the basic street pre-bed above is performed on the road or at the track if installed there…..Perform 10 medium pressure snubs at the track from 80-20mph leaving 300 meters between each snub (approx 0.4g decel). Allow pads to cool for 15 minutes minimum after coasting to the pits allowing brakes to cool a little.
FADE 3 – Perform 6 high-pressure snubs from 90-20mph with a maximum acceleration between consecutive snubs. (approx 0.8g decel, or 80% of an emergency stop). Allow the brakes to fully cool for a minimum of 1 hour before the race session. EBC advise using disc heat paint to ensure green fade is avoided.
EBC RP1/RPX Brake Pad Bedding-in Procedure:
No street pre-bed needed. RP brake pads don’t need to “Warm-up” and are as good as or better than most stock pads in lower-speed highway driving. Full potential comes though when you really work these pads though and that is why they are classed as a race pad.
Track/Race Pre-bed:
For optimum performance perform a single gentle lap to seat brake pads to rotors, followed by fade 3 as below.
FADE 3 – Perform 6 high-pressure snubs from 90-20mph with a maximum acceleration between consecutive snubs. (approx 0.8g decel, or 80% of an emergency stop). Allow the brakes to fully cool for a minimum of 1 hour before the race session. EBC advise using disc heat paint to ensure green fade is avoided.
PBS ProRace/ProComp Brake Pad Bedding-in Procedure:
PBS brake pads are put through a heat curing treatment during the manufacturing process and 'burns out' unwanted materials in advance, reducing the gases that can cause brake fade. Because of this treatment, PBS brake pads only require light 'bedding in'.
It is recommend to perform 10 stops at low pressure and low temperature from 90MPH to approximately 50MPH, and the distance between each brake stop is to be approximately 600 to 800 meters.
PBS brake pads should be bedded in until they are up to mid range working temperature and then allowed to cool properly. Doing this process will help to remove any gases that were in the brake pad compound and will create a perfect contact pattern between the brake disc and the brake pads.
BRAKING NOTICE:
Never hold the pedal down when hot. Coming to a dead stop and holding the footbrake while brake discs are glowing hot will imprint uneven pad deposits onto the brake disc rotor and cause vibration. This is a big NO NO. Always perform a brake cool down drive or perform cool down laps if on a race track to prevent this!
note: image is for illustration purposes and may differ on delivery.
Your selected item
Check availability with our team
Ask us to confirm availability and timing before ordering.
Ask about availabilityPlan your delivery
- Delivery cost
- Calculated at checkout for your address and order.
- Dispatch & arrival
- Dispatch is when your order leaves. Delivery is when it reaches you; check the wording of any estimate shown.
- Need it by a date?
- Check with us before booking fitting or a track day. Estimates depend on availability and the delivery service.

