{"title":"BMW M5 G90 (2024–present)","description":"","products":[{"product_id":"ebc-rp-x-racing-brake-pads-front-bmw-m5-g90","title":"EBC RP-X Racing Brake Pads (FRONT) - BMW M5 G90","description":"\u003cp\u003eFollowing the hugely successful launch of RP-1™, EBC Brakes Racing increases its Motorsport brake pad range with the introduction of our latest ultra-high-performance track \u0026amp; race material, RP-X™.\u003cbr\u003e\u003cbr\u003eDesigned for vehicles driven hard on track, RP-X™ possesses a high friction level of 0.55 between 0-750°C (Ambient-1400°F) and achieves a 100% brake effect from cold. This makes RP-X™ an excellent choice for sprint racing or hill climb events, where full brake performance is essential without requiring any ‘warming up’, but also makes RP-X™ well suited to any type of circuit use where a high initial bite and powerful brake response is desirable.\u003cbr\u003e\u003cbr\u003eEBC Racing would like to emphasise that it is not a case of RP-X™ being ‘better’ than RP-1™, rather it is ‘different’ and designed to provide a distinctly different response characteristic (more aggressive bite) which some drivers may prefer.\u003cbr\u003e\u003cbr\u003eRP-X™ also boasts a flat friction response and is capable of operating at temperatures of up to 750°C without brake fade, yet has a slightly higher average friction of 0.55mu. RP-X™’s higher friction level provides a stronger initial bite and more power under braking, all for a reduced pedal effort compared to RP-1™.\u003cbr\u003e\u003cbr\u003eIf you’ve experienced some of the leading track\/race compounds from EBC’s competitors (such as Pagid RS29, Ferodo DS 1.11 or Endless ME20) then RP-X™ will feel very similar in its response characteristic. The higher friction level and higher initial bite mean RP-X™ is well suited to under-servo’d vehicles (for example: Nissan GT-R R35 and Porsche GT models).\u003cbr\u003e\u003cbr\u003eOn these inherently under-servo’d vehicles the brake system is naturally more progressive and feelsome, therefore a more aggressive pad material such as RP-X™ is preferable to keep pedal travel within the optimum displacement range. However, the extra power served up by RP-X™ isn’t at the expense of exceptional feel during the braking phase, with the material still allowing the driver to modulate the brake pedal with ease and explore the limits in each and every braking zone.\u003cbr\u003e\u003cbr\u003eSimilarly, dedicated track\/race cars that employ aftermarket master cylinders, anti-roll bars and bias adjusters would also be well suited to running RP-X™, since these components allow the driver to fine tune the brake bias to permit the use of a naturally more aggressive pad material.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBrake Pad Features:\u003cbr\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eHigh friction level of 0.55 between 0-750°C (0-1400°F)\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eCapable of operating at temperatures of up to 750C without brake fade.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eMade 100% in EBC Brakes’ Bristol, UK pad factory\u003cbr\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eStainless steel backing plates (reduced heat conduction, no paint)\u003cbr\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eBackplates feature Nucap® NRS® hook pad retention system\u003cbr\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eGood pad life with excellent disc life\u003cbr\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eNOT R90 approved for road use in European markets\u003cbr\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eMade with Nucap NRS hooks on backplates to totally eliminate the chance of pad debond\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eHow to Bed-in EBC RP-1\/RP-X Brake Pads\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eNo street pre-bed needed. RP brake pads don’t need to “Warm-up” and are as good as or better than most stock pads in lower-speed highway driving. Full potential comes though when you really work these pads though and that is why they are classed as a race pad.\u003cbr\u003e\u003cbr\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTrack\/Race Pre-bed\u003cbr\u003e\u003cbr\u003e\u003c\/strong\u003eFor optimum performance perform a single gentle lap to seat brake pads to rotors, followed by fade 3 as below.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFADE 3 \u003c\/strong\u003e– Perform 6 high-pressure snubs from 90-20mph with a maximum acceleration between consecutive snubs. (approx 0.8g decel, or 80% of an emergency stop). Allow the brakes to fully cool for a minimum of 1 hour before the race session. EBC advise using disc heat paint to ensure green fade is avoided.\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003enote: image is for illustration purposes and may differ on delivery.\u003c\/p\u003e","brand":"EBC","offers":[{"title":"Default Title","offer_id":58544250880345,"sku":"DP82331RPX","price":395.16,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/files\/RPX_7196f475-c119-4912-8760-3756abef0884.png?v=1745260049"},{"product_id":"ebc-rp-1-racing-brake-pads-front-bmw-m5-g90","title":"EBC RP-1 Racing Brake Pads (FRONT) - BMW M5 G90","description":"\u003cp\u003eEBC Brakes Racing’s dedicated Motorsport pad RP-1™ pairs high-performance with unprecedented modulation and control, resulting in a track pad that feels uniquely different to the competition and allows drivers to extract every last tenth from each and every braking zone.\u003cbr\u003e\u003cbr\u003eDesigned for vehicles driven hard on track, RP-1™ possesses a moderately high friction level of 0.45 between 100-750°C (200-1400°F). The more progressive response characteristic of RP-1™ makes it well suited for inherently ‘over-servoed’ vehicles where a softer pad material is desirable to allow greater finesse when on the brakes.\u003cbr\u003e\u003cbr\u003eEBC Racing would like to emphasise that it is not a case of RP-1™ being ‘less good’ than RP-X™, rather it is ‘different’ and designed to provide a distinctly different response characteristic (less aggressive bite) which some drivers may prefer.\u003cbr\u003e\u003cbr\u003eRP-1™ boasts a flat friction response averaging 0.45mu and is capable of operating at temperatures of up to 750C without brake fade. However, unlike many other track\/race pad materials on the market, RP-1™ possesses a progressive\/benign response characteristic that provides an exceptional ‘feel’ during each and every braking event.\u003cbr\u003e\u003cbr\u003eThe slightly lower friction level of RP-1™ allows the brake pedal to be worked harder, which is particularly beneficial to cars that are over-servo’d from the factory (for example: Mk7 VW Golf GTI, BMW M cars, Audi RS models, etc). On inherently over-servo’d vehicles, RP-1™ somewhat negates the effect of the over-servo’d brake system setup, resulting in a more progressive and smooth response when driven on track.\u003cbr\u003e\u003cbr\u003eIn some modern vehicles, it can sometimes feel as if all the braking happens in the first inch of pedal travel. Whilst this sharp sensation gives the impression that the car has very ‘good’ brakes to the average driver pootling down to the shops, experienced track\/race drivers know that a hair-trigger brake response is undesirable, verging on totally unacceptable for smooth driving at the limit. A modest amount of brake pedal travel is actually beneficial for performance driving and this is exactly what RP-1™ enables, encouraging the driver to find the limit under braking whilst also enabling trail-braking.\u003cbr\u003e\u003cbr\u003eRP-1™ is particularly suitable for non-ABS assisted vehicles, where a smooth response is essential to avoid locking a wheel under braking. For heavy or inherently under‑servoed vehicles which suit a very aggressive pad, EBC Racing's other track material RP‑X may be preferable.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBrake Pad Features:\u003cbr\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eHigh friction level of 0.45 between 100-750°C (200-1400°F)\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eCapable of operating at temperatures of up to 750C without brake fade.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eMade 100% in EBC Brakes’ Bristol, UK pad factory\u003cbr\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eStainless steel backing plates (reduced heat conduction, no paint)\u003cbr\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eBackplates feature Nucap® NRS® hook pad retention system\u003cbr\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eGood pad life with excellent disc life\u003cbr\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eNOT R90 approved for road use in European markets\u003cbr\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eMade with Nucap NRS hooks on backplates to totally eliminate the chance of pad debond\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eHow to Bed-in EBC RP-1\/RP-X Brake Pads\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eNo street pre-bed needed. RP brake pads don’t need to “Warm-up” and are as good as or better than most stock pads in lower-speed highway driving. Full potential comes though when you really work these pads though and that is why they are classed as a race pad.\u003cbr\u003e\u003cbr\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTrack\/Race Pre-bed\u003cbr\u003e\u003cbr\u003e\u003c\/strong\u003eFor optimum performance perform a single gentle lap to seat brake pads to rotors, followed by fade 3 as below.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFADE 3 \u003c\/strong\u003e– Perform 6 high-pressure snubs from 90-20mph with a maximum acceleration between consecutive snubs. (approx 0.8g decel, or 80% of an emergency stop). Allow the brakes to fully cool for a minimum of 1 hour before the race session. EBC advise using disc heat paint to ensure green fade is avoided.\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003enote: image is for illustration purposes and may differ on delivery.\u003c\/p\u003e","brand":"EBC","offers":[{"title":"Default Title","offer_id":58544257663321,"sku":"DP82331RP1","price":381.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/files\/RP1_c2505133-9142-419d-ade2-9dab1e774108.jpg?v=1745260154"},{"product_id":"ebc-bluestuff-brake-pads-front-bmw-m5-g90","title":"EBC Bluestuff Brake Pads (FRONT) - BMW M5 G90","description":"\u003cp\u003eBluestuff NDX is a high friction sport and race pad that now has R90 approval on almost all fitments for the EU and is therefore totally street legal.\u003cbr\u003e\u003cbr\u003eBluestuff has been used for several seasons in BMW Cup racing with shorter duration and is the EBC Track-day recommended pad. For longer races see the EBC RP or SR ranges. Bluestuff is a popular upgrade brake pad for heavier SUV and 4x4 in street use because of its incredible braking power and high fade resistance and is very popular even on armored street vehicles.\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eBluestuff is an entry-level trackday and race pad that has good street manners and is actually R90 approved for street driving. There are two compounds within the Bluestuff range Bluestuff NDX with higher friction of 0.52 Mu and new Bluestuff B with lower friction of 0.42 Mu.\u003c\/p\u003e\n\u003cp\u003eHowever, due to Bluestuff having excellent cold friction and being very controllable, this compound has quickly become the brake pad of choice for performance road car drivers in USA and Asia markets where R90 homologation does not apply. More recently, EBC is pleased to announce that Bluestuff has passed extensive road-focused testing and gained R90 approval on almost all part numbers, making it unique in being the first truly track-focused pad that is also perfectly legal for use on public roads across Europe. There is no requirement for E.U. customers to inform their insurance company following the fitment of R90 approved pads.\u003c\/p\u003e\n\u003cp\u003eFor customers with experience with EBC’s widely acclaimed Yellowstuff material, Bluestuff boasts a similar friction profile but with a usefully higher friction coefficient across the now larger working range, feeling much like you’d imagine Yellowstuff to feel after a double hit of espresso. Bluestuff has the added benefit of much faster bed in time has a high friction coefficient without feeling grabby, taking things up a notch from EBC’s Yellowstuff material by bringing superb pedal modulation to a trackpad with even greater fade resistance.\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThe target use is for all types of fast and heavier cars in performance and race driving with a much enhanced lifetime over EBC's previous Yellowstuff grade pads.\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eR\u0026amp;D Manager Steve Payne checks out the first batch of the Bluestuff NDX material made with a revolutionary process to produce the highly acclaimed EBC Bluestuff NDX Race Pads. The process involves 5 steps never before used in friction materials and sets EBC Brakes firmly in the lead as a provider of brake friction.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eA great choice for turn-up and race track events due to its short bed in time and medium plus lifetime. This compound has been the choice of the BMW cup series for several seasons.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBrake Pad Features:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e0.52μ stable friction once bedded\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eStrong initial bite, work from cold\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eZero rotor damage\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eCopper free for ECO compliance\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eExcellent upgrade pad for SUV and armoured vehicles in street use\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eR90 approved thus legal for public highway use in European markets\u003c\/li\u003e\n\u003cli\u003eMade with Nucap NRS hooks on back plates to totally eliminate the chance of pad debond\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eHow to Bed-in EBC Bluestuff™ Brake Pads\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003ePerform the street pre-bed Fade 1 routine as below (either on the road or at the track if installed there ) followed by Fade 2 at the race track. The latest Bluestuff DM3362 and Low Mu versions should only take Fade 2 and a 15 minute cooling time to be ready to race.\u003cbr\u003e\u003cbr\u003eFade 3 should not be necessary unless poor disc condition has prevented proper seating but if you have time DO perform Fade 3.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFast Street use Pre-bed\u003cbr\u003e\u003cbr\u003eFADE 1\u003c\/strong\u003e – drive 50 to 100 miles on Public road\/highway normal driving to allow the pads to mate up to the disc and establish full contact followed by 8 stops from 80 mph to 30 mph at 300-yard intervals and then coasting allowing the brakes to cool.\u003cbr\u003e\u003cbr\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTrack\/Race Pre-bed\u003c\/strong\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFADE 2 \u003c\/strong\u003e– After the basic street pre-bed above is performed on the road or at the track if installed there …..Perform 10 medium pressure snubs at the track from 80-20mph leaving 300 meters between each snub (approx 0.4g decel). Allow pads to cool for 15 minutes minimum after coasting to the pits allowing brakes to cool a little.\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFADE 3 \u003c\/strong\u003e– Perform 6 high-pressure snubs from 90-20mph with a maximum acceleration between consecutive snubs. (approx 0.8g decel, or 80% of an emergency stop). Allow the brakes to fully cool for a minimum of 1 hour before the race session. EBC advise using disc heat paint to ensure green fade is avoided.\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003enote: image is for illustration purposes and may differ on delivery.\u003c\/p\u003e","brand":"EBC","offers":[{"title":"Default Title","offer_id":58544369074521,"sku":"DP52331NDX","price":384.01,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/files\/Bluestuff-pads_d113207d-fa16-4ada-94e0-513dcbe47205.jpg?v=1745260261"},{"product_id":"ebc-yellowstuff-brake-pads-front-bmw-m5-g90","title":"EBC Yellowstuff Brake Pads (FRONT) - BMW M5 G90","description":"\u003cp\u003eEven as EBC's world number 1 selling pad grade, the EBC Yellowstuff 3068 compound is new for 2021 and is designed where great stopping power is your goal on fast street use on modern sedans and hot hatches. 100% R90 approved.\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eA high friction pad that works from cold and self seats after installation due to its applied brake-in surface coating. Although the new Yellow grade WILL work fine under shorter duration track, trackday (lapping) use on lighter cars or drifting, \u003c\/span\u003eit does take longer to bed in, and if track driving\u003cspan\u003e is your main purpose, choose Bluestuff or the new RP1 and RPX ranges, or allow extra time for bedding your brakes in.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eEBC Yellowstuff are ECE Brake safety tested, which means they must work perfectly from cold at be at least as good or better than stock pads. When Yellowstuff see some heat (which is not tested for in the ECE R90 brake safety regulations) they really show their pedigree. On Japanese cars built with lower friction FF-rated pads these deliver a full grade higher stopping and on German cars built with GG these are about the only aftermarket pads that will match or beat the pretty good German OE spec pads and that takes some doing.\u003c\/p\u003e\n\u003cp\u003eHigh-efficiency performance pad for high friction and improved stopping power. Not only a high friction pad but very resistant to heat and lots of heavy braking means that Yellowstuff has been used with great success in fast street cars and Police vehicle brakes alike.\u003c\/p\u003e\n\u003cp\u003eEBC Yellowstuff was upgraded during 2021 to remove copper from the mix to comply with environmental legislations and as the new mix lasts longer it is not now being suggested as a track material due to the longer bedding in process required. On the street, bedding happens naturally in the first 100-200 miles of urban use but for those drivers wishing to arrive at the track with new pads and enjoy their day, our current suggestion is to use the Bluestuff formulation for track day driving both front and rear.\u003c\/p\u003e\n\u003cp\u003eBecause of its huge heat range, the applications where EBC Yellowstuff will deliver benefits range from fastest street use on higher horsepower cars on most street-based cars and even as a brake upgrade on Trucks and SUV. Yellowstuff is especially appreciated on Trucks for towing and heavy loads and where wheel and tire oversize upgrades have been fitted. In trackday\/drift\/hillclimb races where earlier Yellow blends were suggested, although track capable, is no longer recommended for track use on most cars due to its long bed-in process. BlueStuff is now EBC's recommended entry-level race pad for all cars, which as a track hybrid is still great on the street and even better on track.\u003c\/p\u003e\n\u003cp\u003eWhen considering full-race use on lighter cars, Yellowstuff has been a strong favorite. It is also the choice of 90% of the Mazda MX5 Miata competitors in the UK race series, used  in drifting and on kit cars. EBC Yellowstuff pads are also used on the UK Silverstone Race Track Drivers experience cars because of their high performance and longevity.  Yellowstuff also claimed a win in the Targa rally and for two years running in the Brazil Mitsubishi off Road Team Desert Challenge.\u003c\/p\u003e\n\u003cp\u003eThe majority of UK Police forces use and love EBC Yellowstuff brake pads. EBC has extended fleet miles and reduced their fleet operating costs by allowing Police Chase cars to drive harder and longer in blue light events. These Police forces have been using EBC Yellowstuff for almost three years now and not one force has had an issue that has caused them to stop buying, they just want more of this fantastic brake product!\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBrake Pad Features:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eHigh friction formula improves brake effect by 15%\u003c\/li\u003e\n\u003cli\u003eOur flagship top selling high friction brake pad for improved braking – UK made and a very high-end pad\u003c\/li\u003e\n\u003cli\u003eSuitable for Fast streetcars, trucks and SUVs wherever a decent brake power upgrade is required.\u003c\/li\u003e\n\u003cli\u003eSuper quiet smooth braking under all conditions, fully shimmed slotted and chamfered construction\u003c\/li\u003e\n\u003cli\u003eExcellent cold bite coupled with high-temperature fade resistance\u003c\/li\u003e\n\u003cli\u003eProgressive braking with unparalleled pedal feel\u003c\/li\u003e\n\u003cli\u003eDrastically reduced stopping distances compared to OE\u003c\/li\u003e\n\u003cli\u003eBrake-In™ coating for accelerated pad bed in period\u003c\/li\u003e\n\u003cli\u003eR90 approved thus legal for public highway use in European markets\u003c\/li\u003e\n\u003cli\u003eFor track use Bluestuff may be a better choice due to bedding in speed which is much shorter with Blue\u003c\/li\u003e\n\u003cli\u003eMade with Nucap NRS hooks on back plates to totally eliminate the chance of pad debond\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eHow to Bed-in EBC Yellowstuff™ Brake Pads\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eEBC brake pads are now mostly self bedding, but for extreme street use please read below.\u003c\/p\u003e\n\u003cp\u003eThe Ultimax2, Greenstuff, Redstuff, and \u003cspan data-mce-fragment=\"1\"\u003eYellow\u003c\/span\u003estuff compound grades come with a brake-in coating that scrubs the rotor surface, accelerates pad seating times, and provides a strong brake effect for the first 100 miles of use as the brake pads seat themselves. After the first 100 miles or so, unless you are going to drive aggressively, there is nothing more to do meaning – most drivers happily use and enjoy their brake’s excellent performance for tens of thousands of miles after this point. If that’s your way of driving, nothing more needs to be explained. Just enjoy your brakes.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFast street driving\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eIf you drive aggressively or in a “Spirited” fashion on roads where it is safe to do so, after seating the pads to your rotors and certainly not before 300 miles of use , you should be prepared for the brake pad to emit an odour or even exhibit some smoke as the pads burn off what EBC call “surface volatiles”.\u003c\/p\u003e\n\u003cp\u003eMany faster drivers experience this in harder braking and criticize the brake pad whereas in fact, this is only part of the final high-end bedding-in process as the pads see rotors temps of 400-500C for the first time (not normal in everyday driving).\u003c\/p\u003e\n\u003cp\u003e\u003cspan data-mce-fragment=\"1\"\u003eOnce seated, any organic brake pad made by EBC performs better once the pad goes through heat curing or what EBC call “Green Fade” which happens during its first severe use. The green fade point is 400C\/650F. There are two ways to know if you have passed the green fade point – one is via the use of heat paints, the second way is to guess. So heat paints are the better option.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eYou should drive with caution until bedded flat and you have passed this green fade point at least twice and then allowed the brake pads to cool so the disc is below 100C.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFast Street use Pre-bed\u003cbr\u003e\u003cbr\u003eFADE 1\u003c\/strong\u003e – drive 50 to 100 miles on Public road\/highway normal driving to allow the pads to mate up to the disc and establish full contact followed by 8 stops from 80 mph to 30 mph at 300-yard intervals and then coasting allowing the brakes to cool.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWanting to use Yellowstuff on the track?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003c\/strong\u003eEBC Yellowstuff are no longer optimum for track use. Bed in times are simply too long to be acceptable. Having said that if you LIKE Yellowstuff and want to use them at the track be prepared for the longer bed-in times detailed below.\u003c\/p\u003e\n\u003cp\u003eYellowstuff, although track-capable, is no longer recommended for track use on most cars due to its long bed-in the process. Bluestuff is now EBC's recommended entry-level race pad for all vehicles, which as a track hybrid is still great on the street and even better on track. But if you are to use Yellowstuff on the track, follow the below Fade procedures;\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFADE 2 \u003c\/strong\u003e– After the basic street pre-bed above is performed on the road or at the track if installed there …..Perform 10 medium pressure snubs at the track from 80-20mph leaving 300 meters between each snub (approx 0.4g decel). Allow pads to cool for 15 minutes minimum after coasting to the pits allowing brakes to cool a little.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eFADE 3 \u003c\/strong\u003e– Perform 6 high-pressure snubs from 90-20mph with a maximum acceleration between consecutive snubs. (approx 0.8g decel, or 80% of an emergency stop). Allow the brakes to fully cool for a minimum of 1 hour before the race session. EBC advise using disc heat paint to ensure green fade is avoided.\u003c\/p\u003e\n\u003cp\u003enote: image is for illustration purposes and may differ on delivery.\u003c\/p\u003e","brand":"EBC","offers":[{"title":"Default Title","offer_id":58544667951449,"sku":"DP42331R","price":349.08,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/files\/Yellowstuff-pads_9bb4e0b4-794b-48aa-a628-5ace697027c1.jpg?v=1745260282"},{"product_id":"ebc-yellowstuff-brake-pads-rear-bmw-m5-g90","title":"EBC Yellowstuff Brake Pads (REAR) - BMW M5 G90","description":"\u003cp\u003eEven as EBC's world number 1 selling pad grade, the EBC Yellowstuff 3068 compound is new for 2021 and is designed where great stopping power is your goal on fast street use on modern sedans and hot hatches. 100% R90 approved.\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eA high friction pad that works from cold and self seats after installation due to its applied brake-in surface coating. Although the new Yellow grade WILL work fine under shorter duration track, trackday (lapping) use on lighter cars or drifting, \u003c\/span\u003eit does take longer to bed in, and if track driving\u003cspan\u003e is your main purpose, choose Bluestuff or the new RP1 and RPX ranges, or allow extra time for bedding your brakes in.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eEBC Yellowstuff are ECE Brake safety tested, which means they must work perfectly from cold at be at least as good or better than stock pads. When Yellowstuff see some heat (which is not tested for in the ECE R90 brake safety regulations) they really show their pedigree. On Japanese cars built with lower friction FF-rated pads these deliver a full grade higher stopping and on German cars built with GG these are about the only aftermarket pads that will match or beat the pretty good German OE spec pads and that takes some doing.\u003c\/p\u003e\n\u003cp\u003eHigh-efficiency performance pad for high friction and improved stopping power. Not only a high friction pad but very resistant to heat and lots of heavy braking means that Yellowstuff has been used with great success in fast street cars and Police vehicle brakes alike.\u003c\/p\u003e\n\u003cp\u003eEBC Yellowstuff was upgraded during 2021 to remove copper from the mix to comply with environmental legislations and as the new mix lasts longer it is not now being suggested as a track material due to the longer bedding in process required. On the street, bedding happens naturally in the first 100-200 miles of urban use but for those drivers wishing to arrive at the track with new pads and enjoy their day, our current suggestion is to use the Bluestuff formulation for track day driving both front and rear.\u003c\/p\u003e\n\u003cp\u003eBecause of its huge heat range, the applications where EBC Yellowstuff will deliver benefits range from fastest street use on higher horsepower cars on most street-based cars and even as a brake upgrade on Trucks and SUV. Yellowstuff is especially appreciated on Trucks for towing and heavy loads and where wheel and tire oversize upgrades have been fitted. In trackday\/drift\/hillclimb races where earlier Yellow blends were suggested, although track capable, is no longer recommended for track use on most cars due to its long bed-in process. BlueStuff is now EBC's recommended entry-level race pad for all cars, which as a track hybrid is still great on the street and even better on track.\u003c\/p\u003e\n\u003cp\u003eWhen considering full-race use on lighter cars, Yellowstuff has been a strong favorite. It is also the choice of 90% of the Mazda MX5 Miata competitors in the UK race series, used  in drifting and on kit cars. EBC Yellowstuff pads are also used on the UK Silverstone Race Track Drivers experience cars because of their high performance and longevity.  Yellowstuff also claimed a win in the Targa rally and for two years running in the Brazil Mitsubishi off Road Team Desert Challenge.\u003c\/p\u003e\n\u003cp\u003eThe majority of UK Police forces use and love EBC Yellowstuff brake pads. EBC has extended fleet miles and reduced their fleet operating costs by allowing Police Chase cars to drive harder and longer in blue light events. These Police forces have been using EBC Yellowstuff for almost three years now and not one force has had an issue that has caused them to stop buying, they just want more of this fantastic brake product!\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBrake Pad Features:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eHigh friction formula improves brake effect by 15%\u003c\/li\u003e\n\u003cli\u003eOur flagship top selling high friction brake pad for improved braking – UK made and a very high-end pad\u003c\/li\u003e\n\u003cli\u003eSuitable for Fast streetcars, trucks and SUVs wherever a decent brake power upgrade is required.\u003c\/li\u003e\n\u003cli\u003eSuper quiet smooth braking under all conditions, fully shimmed slotted and chamfered construction\u003c\/li\u003e\n\u003cli\u003eExcellent cold bite coupled with high-temperature fade resistance\u003c\/li\u003e\n\u003cli\u003eProgressive braking with unparalleled pedal feel\u003c\/li\u003e\n\u003cli\u003eDrastically reduced stopping distances compared to OE\u003c\/li\u003e\n\u003cli\u003eBrake-In™ coating for accelerated pad bed in period\u003c\/li\u003e\n\u003cli\u003eR90 approved thus legal for public highway use in European markets\u003c\/li\u003e\n\u003cli\u003eFor track use Bluestuff may be a better choice due to bedding in speed which is much shorter with Blue\u003c\/li\u003e\n\u003cli\u003eMade with Nucap NRS hooks on back plates to totally eliminate the chance of pad debond\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eHow to Bed-in EBC Yellowstuff™ Brake Pads\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eEBC brake pads are now mostly self bedding, but for extreme street use please read below.\u003c\/p\u003e\n\u003cp\u003eThe Ultimax2, Greenstuff, Redstuff, and \u003cspan data-mce-fragment=\"1\"\u003eYellow\u003c\/span\u003estuff compound grades come with a brake-in coating that scrubs the rotor surface, accelerates pad seating times, and provides a strong brake effect for the first 100 miles of use as the brake pads seat themselves. After the first 100 miles or so, unless you are going to drive aggressively, there is nothing more to do meaning – most drivers happily use and enjoy their brake’s excellent performance for tens of thousands of miles after this point. If that’s your way of driving, nothing more needs to be explained. Just enjoy your brakes.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFast street driving\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eIf you drive aggressively or in a “Spirited” fashion on roads where it is safe to do so, after seating the pads to your rotors and certainly not before 300 miles of use , you should be prepared for the brake pad to emit an odour or even exhibit some smoke as the pads burn off what EBC call “surface volatiles”.\u003c\/p\u003e\n\u003cp\u003eMany faster drivers experience this in harder braking and criticize the brake pad whereas in fact, this is only part of the final high-end bedding-in process as the pads see rotors temps of 400-500C for the first time (not normal in everyday driving).\u003c\/p\u003e\n\u003cp\u003e\u003cspan data-mce-fragment=\"1\"\u003eOnce seated, any organic brake pad made by EBC performs better once the pad goes through heat curing or what EBC call “Green Fade” which happens during its first severe use. The green fade point is 400C\/650F. There are two ways to know if you have passed the green fade point – one is via the use of heat paints, the second way is to guess. So heat paints are the better option.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eYou should drive with caution until bedded flat and you have passed this green fade point at least twice and then allowed the brake pads to cool so the disc is below 100C.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFast Street use Pre-bed\u003cbr\u003e\u003cbr\u003eFADE 1\u003c\/strong\u003e – drive 50 to 100 miles on Public road\/highway normal driving to allow the pads to mate up to the disc and establish full contact followed by 8 stops from 80 mph to 30 mph at 300-yard intervals and then coasting allowing the brakes to cool.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWanting to use Yellowstuff on the track?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003c\/strong\u003eEBC Yellowstuff are no longer optimum for track use. Bed in times are simply too long to be acceptable. Having said that if you LIKE Yellowstuff and want to use them at the track be prepared for the longer bed-in times detailed below.\u003c\/p\u003e\n\u003cp\u003eYellowstuff, although track-capable, is no longer recommended for track use on most cars due to its long bed-in the process. Bluestuff is now EBC's recommended entry-level race pad for all vehicles, which as a track hybrid is still great on the street and even better on track. But if you are to use Yellowstuff on the track, follow the below Fade procedures;\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFADE 2 \u003c\/strong\u003e– After the basic street pre-bed above is performed on the road or at the track if installed there …..Perform 10 medium pressure snubs at the track from 80-20mph leaving 300 meters between each snub (approx 0.4g decel). Allow pads to cool for 15 minutes minimum after coasting to the pits allowing brakes to cool a little.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eFADE 3 \u003c\/strong\u003e– Perform 6 high-pressure snubs from 90-20mph with a maximum acceleration between consecutive snubs. (approx 0.8g decel, or 80% of an emergency stop). Allow the brakes to fully cool for a minimum of 1 hour before the race session. EBC advise using disc heat paint to ensure green fade is avoided.\u003c\/p\u003e\n\u003cp\u003enote: image is for illustration purposes and may differ on delivery.\u003c\/p\u003e","brand":"EBC","offers":[{"title":"Default Title","offer_id":58544684892505,"sku":"DP42526R","price":133.97,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/files\/Yellowstuff-pads_9bb4e0b4-794b-48aa-a628-5ace697027c1.jpg?v=1745260282"},{"product_id":"ebc-bluestuff-brake-pads-rear-bmw-m5-g90","title":"EBC Bluestuff Brake Pads (REAR) - BMW M5 G90","description":"\u003cp\u003eBluestuff NDX is a high friction sport and race pad that now has R90 approval on almost all fitments for the EU and is therefore totally street legal.\u003cbr\u003e\u003cbr\u003eBluestuff has been used for several seasons in BMW Cup racing with shorter duration and is the EBC Track-day recommended pad. For longer races see the EBC RP or SR ranges. Bluestuff is a popular upgrade brake pad for heavier SUV and 4x4 in street use because of its incredible braking power and high fade resistance and is very popular even on armored street vehicles.\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eBluestuff is an entry-level trackday and race pad that has good street manners and is actually R90 approved for street driving. There are two compounds within the Bluestuff range Bluestuff NDX with higher friction of 0.52 Mu and new Bluestuff B with lower friction of 0.42 Mu.\u003c\/p\u003e\n\u003cp\u003eHowever, due to Bluestuff having excellent cold friction and being very controllable, this compound has quickly become the brake pad of choice for performance road car drivers in USA and Asia markets where R90 homologation does not apply. More recently, EBC is pleased to announce that Bluestuff has passed extensive road-focused testing and gained R90 approval on almost all part numbers, making it unique in being the first truly track-focused pad that is also perfectly legal for use on public roads across Europe. There is no requirement for E.U. customers to inform their insurance company following the fitment of R90 approved pads.\u003c\/p\u003e\n\u003cp\u003eFor customers with experience with EBC’s widely acclaimed Yellowstuff material, Bluestuff boasts a similar friction profile but with a usefully higher friction coefficient across the now larger working range, feeling much like you’d imagine Yellowstuff to feel after a double hit of espresso. Bluestuff has the added benefit of much faster bed in time has a high friction coefficient without feeling grabby, taking things up a notch from EBC’s Yellowstuff material by bringing superb pedal modulation to a trackpad with even greater fade resistance.\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThe target use is for all types of fast and heavier cars in performance and race driving with a much enhanced lifetime over EBC's previous Yellowstuff grade pads.\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eR\u0026amp;D Manager Steve Payne checks out the first batch of the Bluestuff NDX material made with a revolutionary process to produce the highly acclaimed EBC Bluestuff NDX Race Pads. The process involves 5 steps never before used in friction materials and sets EBC Brakes firmly in the lead as a provider of brake friction.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eA great choice for turn-up and race track events due to its short bed in time and medium plus lifetime. This compound has been the choice of the BMW cup series for several seasons.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBrake Pad Features:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e0.52μ stable friction once bedded\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eStrong initial bite, work from cold\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eZero rotor damage\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eCopper free for ECO compliance\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eExcellent upgrade pad for SUV and armoured vehicles in street use\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eR90 approved thus legal for public highway use in European markets\u003c\/li\u003e\n\u003cli\u003eMade with Nucap NRS hooks on back plates to totally eliminate the chance of pad debond\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eHow to Bed-in EBC Bluestuff™ Brake Pads\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003ePerform the street pre-bed Fade 1 routine as below (either on the road or at the track if installed there ) followed by Fade 2 at the race track. The latest Bluestuff DM3362 and Low Mu versions should only take Fade 2 and a 15 minute cooling time to be ready to race.\u003cbr\u003e\u003cbr\u003eFade 3 should not be necessary unless poor disc condition has prevented proper seating but if you have time DO perform Fade 3.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFast Street use Pre-bed\u003cbr\u003e\u003cbr\u003eFADE 1\u003c\/strong\u003e – drive 50 to 100 miles on Public road\/highway normal driving to allow the pads to mate up to the disc and establish full contact followed by 8 stops from 80 mph to 30 mph at 300-yard intervals and then coasting allowing the brakes to cool.\u003cbr\u003e\u003cbr\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTrack\/Race Pre-bed\u003c\/strong\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFADE 2 \u003c\/strong\u003e– After the basic street pre-bed above is performed on the road or at the track if installed there …..Perform 10 medium pressure snubs at the track from 80-20mph leaving 300 meters between each snub (approx 0.4g decel). Allow pads to cool for 15 minutes minimum after coasting to the pits allowing brakes to cool a little.\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFADE 3 \u003c\/strong\u003e– Perform 6 high-pressure snubs from 90-20mph with a maximum acceleration between consecutive snubs. (approx 0.8g decel, or 80% of an emergency stop). Allow the brakes to fully cool for a minimum of 1 hour before the race session. EBC advise using disc heat paint to ensure green fade is avoided.\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003enote: image is for illustration purposes and may differ on delivery.\u003c\/p\u003e","brand":"EBC","offers":[{"title":"Default Title","offer_id":58544708714841,"sku":"DP52526NDX","price":147.36,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/files\/Bluestuff-pads_d113207d-fa16-4ada-94e0-513dcbe47205.jpg?v=1745260261"},{"product_id":"bimecc-steel-wheel-bolts-chrome-tapered-bmw-m5-g90","title":"Bimecc Steel Wheel Bolts (Chrome) Tapered - BMW M5 G90","description":"\u003cp\u003eBimecc Wheel bolts are both solid and durable.\u003c\/p\u003e\n\u003cp\u003eHigh Torque tested to 270 ft\/lbs. T6 Heat-treated.\u003c\/p\u003e\n\u003cp\u003eTapered fitment.\u003c\/p\u003e\n\u003cp\u003eAvailable in various lengths.\u003c\/p\u003e\n\u003cp\u003eSold individually.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBolt Length Sizes:\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e28mm - Approx Factory length\u003c\/li\u003e\n\u003cli\u003e40mm - For use with 10, 12 or 15mm wheel spacers\u003c\/li\u003e\n\u003cli\u003e45mm - For use with 20mm wheel spacers\u003c\/li\u003e\n\u003cli\u003e50mm - For use with 20 or 25mm wheel spacers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNote: These wheel bolt heads are the same size as factory wheel bolts.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"Bimecc","offers":[{"title":"28mm","offer_id":58545442455897,"sku":"C17F27","price":1.64,"currency_code":"GBP","in_stock":true},{"title":"40mm","offer_id":58545442488665,"sku":"C17F40","price":1.84,"currency_code":"GBP","in_stock":true},{"title":"45mm","offer_id":58545442521433,"sku":"C17F45","price":1.84,"currency_code":"GBP","in_stock":true},{"title":"50mm","offer_id":58545442554201,"sku":"C17F50","price":1.84,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/files\/BimeccTaperedWheelBolt_2e9bb1d2-24e8-41a8-9ba5-2dee3dd899a7.jpg?v=1773164479"},{"product_id":"bimecc-steel-wheel-bolts-black-tapered-bmw-m5-g90","title":"Bimecc Steel Wheel Bolts (Black) Tapered - BMW M5 G90","description":"\u003cp\u003eBimecc Wheel bolts are both solid and durable.\u003c\/p\u003e\n\u003cp\u003eHigh Torque tested to 270 ft\/lbs. T6 Heat-treated.\u003c\/p\u003e\n\u003cp\u003eTapered fitment.\u003c\/p\u003e\n\u003cp\u003eAvailable in various lengths.\u003c\/p\u003e\n\u003cp\u003eSold individually.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBolt Length Sizes:\u003c\/strong\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e28mm - Approx Factory length\u003c\/li\u003e\n\u003cli\u003e40mm - For use with 10, 12 or 15mm wheel spacers\u003c\/li\u003e\n\u003cli\u003e45mm - For use with 20mm wheel spacers\u003c\/li\u003e\n\u003cli\u003e50mm - For use with 20 or 25mm wheel spacers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNote: These wheel bolt heads are the same size as factory wheel bolts.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"Bimecc","offers":[{"title":"28mm","offer_id":58545483022681,"sku":"C17F27-ZINNI","price":1.84,"currency_code":"GBP","in_stock":true},{"title":"40mm","offer_id":58545483055449,"sku":"C17F40-ZINNI","price":2.2,"currency_code":"GBP","in_stock":true},{"title":"45mm","offer_id":58545483088217,"sku":"C17F43-ZINNI","price":2.2,"currency_code":"GBP","in_stock":true},{"title":"50mm","offer_id":58545483120985,"sku":"C17F50-ZINNI","price":2.45,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/files\/BimeccTaperedWheelBolt_black.jpg?v=1773164491"},{"product_id":"bimecc-steel-wheel-nuts-tapered-bmw-m5-g90","title":"Bimecc Steel Wheel Nuts (Tapered) - BMW M5 G90","description":"\u003cp\u003eBimecc Wheel Nuts are made from high strength steel and are coated in heavy duty black, making them ideal for track use.\u003c\/p\u003e\n\u003cp\u003ePerfect for use with any Bimecc Wheel Bolt To Wheel Stud Conversion Kit.\u003c\/p\u003e\n\u003cp\u003eSuitable for Motorsport use.\u003c\/p\u003e\n\u003cp\u003eSold in sets of 20.\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003enote: image is for illustration purposes and may differ on delivery\u003c\/span\u003e\u003c\/p\u003e","brand":"Bimecc","offers":[{"title":"I accept that these are wheel nuts and not wheel bolts.","offer_id":58545490919769,"sku":"B-WNX20-M14125","price":30.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/files\/rival_open_ended_steel_wheel_nuts_1_2_266713f8-f3ba-4443-bd02-aadc9d130540.jpg?v=1745370969"},{"product_id":"rival-copper-wheel-nuts-tapered-bmw-m5-g90","title":"Rival Copper Wheel Nuts (Tapered) - BMW M5 G90","description":"\u003cp\u003eRival Performance Copper Plated Wheel Nuts provide a performance, luxury and a unique look to your alloy wheels.\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eAlso offers heat resistance, anti-seizing properties and corrosion resistance.\u003c\/span\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003ePerfect for use with any wheel bolt to wheel stud conversion kit.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eTapered seat fitment, and sold in sets of 20.\u003cbr\u003e\u003cbr\u003eA must-have upgrade.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003enote: image is for illustration purposes and may differ on delivery\u003c\/span\u003e\u003c\/p\u003e","brand":"Rival Performance","offers":[{"title":"I accept that these are wheel nuts and not wheel bolts.","offer_id":58545528701273,"sku":"R-CWNS-M14125","price":99.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/files\/RIVAL-CWN.png?v=1774289714"},{"product_id":"bimecc-wheel-stud-nut-conversion-kit-bmw-m5-g90","title":"Bimecc Wheel Stud \u0026 Nut Conversion Kit - BMW M5 G90","description":"\u003cp\u003eBimecc Wheel Stud \u0026amp; Nut Conversion Kits, made in Italy, are crafted from 10.9 strength rating cold forged steel. Renowned for their quality, they are used in racing and motorsport events worldwide, making them ideal for those wanting to eliminate wheel bolts.\u003c\/p\u003e\n\u003cp\u003ePaired with open ended wheel nuts of the same thread pitch.\u003c\/p\u003e\n\u003cp\u003eSold as a set of 20.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eManufactured From Cold Forged Steel (10.9 Strength Rating)\u003c\/li\u003e\n\u003cli\u003eAvailable in 75mm, 82mm or 90mm Stud Length\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eSize Specifications:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e75mm - For use with or without 10mm spacers (15mm threaded hub length | 55mm threaded nut length)\u003c\/li\u003e\n\u003cli\u003e82mm - For use with 15mm spacers (15mm threaded hub length | 62mm threaded nut length)\u003c\/li\u003e\n\u003cli\u003e90mm - For use with 20mm spacers (15mm threaded hub length | 70mm threaded nut length)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eInstallation Process:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eWhen installing each wheel stud into the wheel hub, the use of thread lock such as Loctite 242 Blue must be used in order to ensure the wheel stud stays secured to the hub. Loctite 242 Blue is vibration resistant \u0026amp; good for up to 149degrees Celsius.\u003c\/li\u003e\n\u003cli\u003eEach wheel stud is to be torqued to 14NM, and each wheel nut is to be torqued to the same rating as the original car manufactures factory wheel bolt torque rate\u003c\/li\u003e\n\u003cli\u003eAfter approximately 50-60miles worth of use, check that the wheel nut torque rating has remained the same and re-torque if needed.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003enote: image is for illustration purposes and may differ on delivery.\u003c\/p\u003e","brand":"Bimecc","offers":[{"title":"75mm","offer_id":58545540006233,"sku":"RM-WSNCK-M1425-75","price":89.99,"currency_code":"GBP","in_stock":true},{"title":"82mm","offer_id":58545540039001,"sku":"RM-WSNCK-M1425-82","price":89.99,"currency_code":"GBP","in_stock":true},{"title":"90mm","offer_id":58545540071769,"sku":"RM-WSNCK-M1425-90","price":89.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/files\/wheel-studs_0aa57305-4307-4f10-9fd1-c49740169c28.jpg?v=1745270561"},{"product_id":"bimecc-slip-on-hubcentric-wheel-spacers-5x112-bmw-m5-g90","title":"Bimecc Slip-on Hubcentric Wheel Spacers (5x112) - BMW M5 G90","description":"\u003cp\u003eBimecc Hubcentric Wheel Spacers are made from high quality aluminium, and are CNC lathed \u0026amp; milled to ensure precision fitment.\u003c\/p\u003e\n\u003cp\u003eIdeal for extending the axle\/track width, fill the arches or improve the overall look of the car.\u003c\/p\u003e\n\u003cp\u003eBlack coated for added durability.\u003c\/p\u003e\n\u003cp\u003eSuitable for road \u0026amp; track use.\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eSold as a 2 piece set, ready to put onto either the front or rear hubs.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePCD: \u003cspan data-mce-fragment=\"1\"\u003e5x112\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eCentre Bore: 66.6\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003enote: image is for illustration purposes and may differ on delivery\u003c\/p\u003e","brand":"Bimecc","offers":[{"title":"10mm","offer_id":58545572708697,"sku":"511210666-SB-AL","price":69.99,"currency_code":"GBP","in_stock":true},{"title":"12mm","offer_id":58545572741465,"sku":"511212666-AL","price":69.99,"currency_code":"GBP","in_stock":true},{"title":"15mm","offer_id":58545572774233,"sku":"SPK100A","price":69.99,"currency_code":"GBP","in_stock":true},{"title":"20mm","offer_id":58545572807001,"sku":"SPK100","price":69.99,"currency_code":"GBP","in_stock":true},{"title":"25mm","offer_id":58545572839769,"sku":"SPK100E","price":69.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/files\/BIMECCSPACERs_842f2adf-2bbd-4793-a081-dbd02a2882ac.jpg?v=1745269893"},{"product_id":"genuine-bmw-oil-filter-bmw-m5-g90","title":"Genuine BMW Oil Filter - BMW M5 G90","description":"\u003cp\u003eA Genuine BMW Oil Filter ensures clean, circulating oil enters your engine by effectively removing soot, oil carbons, dust and metal particles from the engine oil.\u003cbr\u003e\u003cbr\u003eMade from high quality material, the filter gives your engine optimum protection from contaminants, minimizing engine wear for the entire interval between services, prolonging your engine’s life.\u003cbr\u003e\u003cbr\u003eThe engine oil filter plays a vital role in the regular servicing and maintenance of any internal combustion engine. The aim of the oil filter is too catch any abrasive particles, small shavings of metal and contaminants that may be in the engine oil and prevent them from continuing to exist in the remainder of the oil. Essentially, the oil filter filters the engine oil.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eFitment:\u003c\/strong\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eBMW S63\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003enote: check all connections at regular intervals, especially during the first few miles after installation, to inspect for leaks.\u003c\/p\u003e\n\u003cp\u003enote: image is for illustration purposes and may differ on delivery\u003c\/p\u003e","brand":"BMW","offers":[{"title":"Default Title","offer_id":58546208899417,"sku":"B-11425A33C43","price":38.69,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/files\/bmw-11425A33C43.jpg?v=1783627990"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0933\/7765\/9225\/collections\/bmw-main-collection_afec50a2-106a-4d21-af05-08338835a484.png?v=1783628904","url":"https:\/\/www.rivalperformance.co.uk\/collections\/bmw-m5-g90-2024-present.oembed","provider":"Rival Performance","version":"1.0","type":"link"}